 |
UNIT PRICE
$3.85 |
Gauge
HO & N |
Item#
5001 |
| GENERAL USES: 1. Square cut flex-track on straightways and curves with out ties separation. 2. Will help locate mis-aligned rail joints. 3. Straighten used flex track in seconds. |
| HOW TO USE: Snap tool on track, use edge for straight edge cut. Slide tool along track while spiking track down, or straighten track by pulling track through tool. |
SOLDERING TOOL
 |
UNIT PRICE
$3.85 |
Gauge
N |
Item#
5004 |
| GENERAL USES: 1. Tool snaps on rail holding rails in alignment while soldering. 2. Also acts as a heat sink. |
| HOW TO USE: Place tool on rails so the openings are over rail joints. Solder outside edge of rails. If insulators are used, spike rails down instead of soldering. |
BALLAST SPREADER
 |
UNIT PRICE
$10.05 |
Gauge
HO |
Item#
5008 |
| GENERAL USES: 1. Quick and easy way for ballasting. 2. Tool applies ballast on both sides of the rail along with a nice even layer between rails. |
| HOW TO USE: Set spreader on track with bottom indicator facing in the direction you are going to ballast. Twist tube right or left until holes close. Fill tube with ballast, align bottom and top indicator dots and slide spreader along track, moving slowly until you become accustomed to the speed ballast comes out. When you reach a place you want to stop, turn spreader 1/4 turn to the left or right. To remove spreader from track, lift by bottom ring to insure spreader does not come apart. |
Order Now ][Return to Top][Next Tool
 |
UNIT PRICE
$3.85 |
Gauge
HO,N, & HOn3 |
Item#
5002 |
| GENERAL USES: 1. This single tool will allow you to maintain uniform spacing on straightaways and curves while laying parallel tracks. |
| HOW TO USE: Place tool on stationary track. Set second track in remaining slot and slide tool along tracks. Tool will set second track, while spiking. |
RADIUS TOOL
 |
UNIT PRICE
$8.57 |
Gauge
N/A |
Item#
5007 |
| GENERAL USES: 1. This tool will enable the novice and craftsman to lay precision radi quickly and easily. 2. No more guess work or broken strings. |
| HOW TO USE: Your radius tool set consists of two units. The short unit will swing a radius from 7" to 11". The long unit from 11" to 23". Numbers on the face of the tool are full value. Unmarked holes are 1/2 value. To use tool, remove pencil from shipping ball and place in large hole, point facing unmarked side of tool. After determining the size of the radius, insert point with ball top in proper hole. Press down on ball and swing radius to the desired length. |
FLEX-TRACK ALIGNMENT TOOL & NAILING FIXTURE
 |
UNIT PRICE
$5.15 |
Gauge
N |
Item#
5015 |
| GENERAL USES: 1. Nailing fixture keeps track square and straight while fastening ties through cutouts. |
| HOW TO USE: Place 1st section of flex-track on layout diagram. Fasten down tie closest to end where hole appears in tie. Place tool on track making sure both rails are in track grooves. Slide tool along track, fastening ties through cut-outs in center of tool. |
Track Tool Set
|
UNIT PRICE
$20.57 |
Gauge
N |
Item#
5011 |
| The Track Tool Set Contains 1 unit each of: Track Tool, Parallel Tool, Soldering Tool, and Ballast Spreader. |
Order Now ][Return to Top][Deluxe Tool Set
Deluxe Tool Set
|
UNIT PRICE
$35.09 |
Gauge
N |
Item#
5018 |
| Deluxe Tool Set Contains 1 unit each of: Track Tool, Parallel Tool, Soldering Tool, Radius Tool, Alignment tool and Ballast Spreader. |
MLRMFG.com Front Page ][ Advertise on MLR Today! ][ E-Mail Webmaster
MLR MFG
1850 Juanita Lane
Fallbrook, Ca 92028